|
Who's Online
There currently are 6024 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
Circuit Description
3-8-4-2. The Concept of Fixed Lamp Control For �xed lamp control, the logic unit "fuser on" control signal and SMPS unit DC power must be supplied. This circuit turns on only when "fuser on" sends the signal and the DC power is supplied. The following explains how the �xed lamp control circuit works. logic unit "fuser on" sends trigger current to triac driver PC3 LED, then the infrared ray is detected by PC3 photo detector. Next, YC3 triac is conducted. The conducted current sends trigger input to triac SY1 gate. At this point, SY1 is conducted and AC power is supplied to �xed lamp. Lamp is turned on and temperature rises. As this �xed lamp control circuit uses the AC voltage ("+" and "-" are repeated) as the power supply, it used two-way triac (SY1), which has advantage over one-way SCR considering the price, size and reliability. Triac's gate can be triggered by either forward or reverse signal. Once triac is turned on, it will not be controlled by gate signal, but will be continuously on until the current between major terminals decreases below the holding current. In other words, you cannot turn it off with reverse signal unlike SCR. This property is called current-voltage threshold rise rate (commutation: dv/dt). In AC power control application, triac has to turn off conduction in each zero crossing or switch it twice in each cycle. This switching operation is called commutation. It is possible to turn off the triac at the end of half cycle by eliminating the gate signal when the load current (IL) is gained at the level equal to or lower than holding current. When triac commutes off-line, the direction of the voltage of the both ends of triac will be reversed and increase up to the maximum value of line voltage (VAC). At this point, the width of rise rate will be determined by dv/ dt and overshoot voltage, by the circuit. When triac commutes off-line, the voltage of both ends of triac will have the same voltage as the line voltage.
IL Inductive IL VAC G
<Inductive Circuit>
VT
Samsung Electronics
- This Document can not be used without Samsung's authorization -
3-39
|
|
|
> |
|