|
Who's Online
There currently are 5574 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
It is wonderful done!!! a great job in scanning the manual. Superior quality in all the electric scheme. Very understandable and net!!! Thank you!
;
muy buen manual por lo completo de este algunos esquemas estan muy divididos lo que hace algo dificil el seguimiento.
;
very good manual, with detail and clarity in esquematic diagrams and waveforms .
;
Very quality copy of original service manual, which contains the circuit diagrams, PCB and lists of components, well as recommendation for calibration procedures of device, also everything else, that need for repair, tuning and use this oscilloscope.
All presented copies have high-resolution, so you can view all in detail.
This manual will very useful for simple owners and for repairers.
I recommend these manual, because myself is owner of Philips PM3216 and I need sometimes servicing these oscilloscope (principally calibrating).
Also, these document is an example of excellent design of technical documentation.
;
Excellent printing quality.
A complete and very usefull service manual with all details.
GREAT SERVICE AT VERY LOW PRICE!
A+++++++++++++++++++++++++
3. Data Transfer program
When the main board of a customer's cellular phone is required to be replaced with a new one, or the customer is needed to use a phone lent from the service center while his phone is serviced, this feature is used to transfer(copy) all the EEPROM data of the customer's phone into the new board or the lent phone to keep the information the customer had stored into his phone personally. 3. Press <F1> key to read EEPROM data from the customer's cellular phone. On screen, 'Change the mode of the phone from HANDS-FREE mode to DM mode' message appears. On the LCD display of the phone, 'AUTO TEST' and 'WRITE EEPROM' messages appear. If the phone is already in DM(Diagnostic Monitor) mode, the message does not appear. 4. After the mode is changed to DM, EEPROM data on the cellular phone is read by PC. You can monitor the reading procedure on the screen. 5. When the data reading is completed, 'Replace the source phone with the target phone and press <F5> when ready' message appears on the screen. 6. Press any key to clear the message. The cellular phone displays 'DELETED' and '300-300-3000' instead of greeting and phone number respectively. All the features of the phone including ESN are reset to default status, and the phone can not be operated. 7. Remove the phone from the test jig and connect the new phone to the test jig. Caution: If you try to perform reading again without writing after reading is already done once, the error message 'READING FROM THE PHONE WAS ALREADY BEEN CARRIED OUT, WRITING SHOULD BE CARRIED OUT' appears on the screen. 8. Press <F5> key to perform writing EEPROM data. You can monitor the writing procedure on the screen. 9. When the data writing is completed, the phone will reset. The program returns to standby mode and is ready to read data from another phone. 'WELL DONE, DATA TRANSFER IS COMPLETED' appears on the screen. 10. Check if the transferred EEPROM data is the same.
3-1 Getting Started
1. Run the DTRANxx.EXE file. If you run the file for the first time, the message 'INITIAL FILE IS CREATED' appears. Do not delete the created file because the file creates DTRANxx.CFG to store environment setup data. The message does not appear once you have run the program. 2. Press any key to go to next procedure. Function Keys Fl Reads EEPROM data from the customer's cellular phone. F5 Writes the data of the customer's phone into the EEPROM on the new board.
ALT+X Exits programming and returns to DOS mode.
3-2 Operation Procedure
1. On standby mode, 'Please check the communication link between your PC and the phone prior to beginning ...' messages appear on the screen. You are ready to transfer data. 2. Switch the phone power on after you have run the program.
Samsung Electronics
3-1
|
|
|
> |
|